Description

Armor Plate 800-2 is a bisphenol slurry coat that is primarily used to prime concrete substrates prior to the application of the Armor Plate 800 Lining System. Armor Plate 800-2 also bonds to steel and wood, and it will saturate fiberglass mat and cloth. AP 800-2 is an inert-filled resin that:

  • fills voids
  • reduces moisture transmission through concrete
  • reduces coefficient of expansion

Chemical Resistance

Armor Plate 800-2 is chemically resistant to acids, salts, caustics, petroleum solvents and some bleaches. Contact the Wil-Cor, Inc. Technical Department for chemical resistance in specific service conditions.

Physical properties

Weight / Gallon 10.5 lbs
Water Absorption 0.035%
Mixing Ratio 1.25-2.0 oz. catalyst / gal. resin
Pot Life @ 75 °F 10 min.
Maximum Service Temperature 210 °F
Flash Point 85 – 90 °F
Shrinkage 0.004%
Shelf Life @ 77 °F 3 – 4 months

Installation Recommendation

Wil-Cor, Inc. recommends supervision by Wil-Cor or that this product be installed by experienced fiberglass installers. Preparation, mixing and application information is provided for installers with adequate installation experience.

Mixing

Mix resin (part A) and catalyst (part B) at the job site, immediately prior to application. The pot life of AP 800-2 is very short (10 min.) so only mix quantities that can be used during a 10-minute period.

The mixing ratio of resin : catalyst will vary with temperature. The catalyst is Armor Plate 60, methyl ethyl ketone peroxide. Use 1.25 to 2.0 oz. of catalyst for each gallon of resin.

Surface Preparation

A clean surface is necessary to properly apply the Armor Plate 800-2. Remove dirt, oil and other contaminants by sandblasting or other mechanical methods. All surfaces must be dry before AP 800-2 is applied.

Application

Armor Plate 800-2 may be applied with a brush, roller, squeegee or by spray equipment.

Packaging

Armor Plate 800-2 is available in a 5-gallon pail.

Coverage and Estimating

The approximate coverage of Armor Plate 800-2 is 75 sq. ft. / gallon, depending on the surface texture.

Shelf Life

The expected shelf life of the Armor Plate 800-2 is 3 – 4 months when sealed tightly and stored at temperatures around 75 °F.

Freight Classification

Resin Solution, Flammable Liquid

Warning

For Industrial Use Only! – Flammable Liquid

Resin Component

  • Causes eye or skin irritation. Always wear suitable clothing to minimize skin Contact.
  • Vapor caused headache, dizziness, nausea and unconsciousness. Area must be ventilated. If inhaled, remove victim to fresh air. Give artificial respiration if not breathing.
  • For eye Contact, flush with water immediately.
  • For skin Contact, wash with soap and water immediately. Remove contaminated clothing.
  • If swallowed, give large amounts of milk or water to drink and seek immediate medical attention.
  • Flammable. Keep away from all sparks, flames or heat. Extinguish fires with foam, dry chemical, carbon dioxide or water spray.

Hardener – AP 60 (Methyl Ethyl Ketone Peroxide)

  • Store in a cool place away from all sources of heat.
  • NEVER store near cobalt naphthenate or other promotors, accelerators or strong reducing agents.
  • Strong irritant. Ingestion can be fatal. If swallowed, induce vomiting and call physician.
  • For eye contact, flush with water for 30 minutes and call physician immediately.
  • For skin contact, wash with soap and water immediately. Remove contaminated clothing.

Before use, review Material Safety Data Sheet for further information. Read and follow the hazard information and first aid directions on each product label before using.